Well Traveled Living Indoor Fireplace 60354 User Manual

ELECTRIC FIREPLACE  
CARE & USE GUIDE  
Please read this manual before  
installing and using your fireplace  
IF THE INFORMATION IN THIS  
MANUAL IS NOT FOLLOWED  
EXACTLY, AN ELECTRICAL SHOCK  
OR FIRE MAY RESULT CAUSING  
PROPERTY DAMAGE, PERSONAL  
INJURY OR LOSS OF LIFE  
 
Use this appliance only as described in this manual. Any other use not recommended  
by the manufacturer may cause fire, electric shock or injury to persons.  
Avoid the use of an extension cord because the extension cord may overheat and  
cause a risk of fire. However, if you have to use an extension cord, the cord shall be  
14 gauge minimum size and rated not less that 2025 watts. The extension cord must  
be a three wire cord with grounding type plug and cord connector. The extension  
cord shall not be more than 20 feet in length.  
17.  
18.  
SPECIFICATIONS  
Dimensions LxWxH  
15.76” x 26” x 28.37”  
59.40 lbs  
110V  
Net Weight  
Voltage  
Frequency  
Watts  
60 Hz  
1350 W  
Heater Rating  
4600 BTU  
ELECTRICAL CONNECTION  
A 15 Amp, 110 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this  
appliance. The fireplace must be on a dedicated circuit as other appliances on the same  
circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in opera-  
tion. The unit comes standard with a 6.5 ft long 3 wire cord, exiting out the back of the  
fireplace. Plan the installation to avoid the use of an extension cord. If an extension cord  
must be used, it must be a minimum 14 gauge, 3 wire with grounding type plug and  
connector and rated not less than 2025 watts. The extension cord shall not be more than  
20 ft in length.  
WARNING: Electrical outlet wiring must comply with local building codes and other  
applicable regulations to reduce the risk of fire, electrical shock and injury to persons.  
WARNING: Do not use this fireplace if any part of it has become wet. Immediately call a  
qualified service technician to inspect the fireplace and replace any part of the electrical  
system which has been wet.  
 
SERVICE INSTRUCTIONS  
FOR YOUR SAFETY  
Service must be performed by a qualified service agency.  
REtPLACING THE LIGHT BULBS  
This fireplace uses 2 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base,  
chandelier candle type bulbs). The access plate is located on the back of the unit. For  
convenience, if one of the light bulbs burns out, it may be easier to replace both of the  
light bulbs at the same time.  
WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may result in a  
fire, causing property damage, personal injury or loss of life.  
1. Turn off the power to the unit, and unplug it from the electrical outlet.  
2. Let the fireplace cool if it has been operating.  
3. Turn the fireplace so you are facing the back of the fireplace.  
4. Look for the access plate with the gold printing on it.  
5. Remove the 3 screws holding the access plate in position. Once you have removed  
the 3 screws, lift the access plate so the 2 positioning tabs come free of their slots.  
Once you have removed the access plate you can see and access the two 40 watt  
chandelier bulbs.  
6. Remove each light bulb by unscrewing them out of the bases, turning them  
counterclockwise. You can use one hand to hold the light socket in place, if required.  
7. Install the new light bulbs by turning each light bulb into the base clockwise. You can  
use one hand to hold the light socket in place, if required.  
8. Replace the access plate by inserting the 2 tabs, pushing the plate up against the  
fireplace back, and inserting the 3 screws.  
9. Turn the fireplace back so you are facing the front of the fireplace.  
10. Plug the fireplace back into the electrical outlet and turn the power on and enjoy the  
flame effect.  
SERVICE INSTRUCTIONS  
Your fireplace has the following functions:  
Leg Assembly:  
Lay stove on a flat surface. Attach  
4 legs with screws provided as  
shown in Fig. 1:  
Low heat  
700 watts  
On/Off  
Power to the uni  
High heat  
1350 watts  
Fig. 1  
Please note: Both the low heat and high heat  
 
switches must be in the on position to achieve high heat.  
 

Weslo Treadmill WLTL39092 User Manual
Westinghouse Camping Equipment 64001 User Manual
Whirlpool Dishwasher ADP 4300 WH User Manual
Whirlpool Double Oven W10748900C User Manual
Whirlpool Freezer EV120NXRQ00 User Manual
Whirlpool Refrigerator 2184589 User Manual
White Rodgers Humidifier HFT2100 User Manual
White Rodgers Thermostat 1F87 51 User Manual
Xpelair Ventilation Hood 91189AW User Manual
Zhone Technologies Network Router 6652 A2 User Manual